POWER COMMANDER V

powercommander_v_fi_banner

LOADED WITH TONS OF NEW FEATURES

The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models. Below you will find some Power Commander V features.
pcom_v_with_logo
  • Reduced size from PCIIIusb (less than half of the size of PCIII)
  • USB powered from computer (9 volt adapter is no longer needed for programming)
  • 2 position map switching function built in (map switch not included)
  • Gear input (allows for map adjustment based on gear and speed)
  • Analog input (allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature)
  • With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear (for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables).
  • Unit has a -100/+250% fuel change range (up from -100/+100%). This allows more adjustment range for 8 injector sportbikes
  • 10 throttle position columns (up from 9 on PCIIIusb)
  • Enhanced “accel pump” utility (increased adjustment and sensitivity ranges)

NEW Power Commander V w/ Built in Ignition Control

On select models, gain control over fuel delivery AND timing with the new Power Commander V with fuel and ignition control. The best of both worlds, now you can realize all the benefits of the Power Commander V and the Ignition Module 5 wrapped in a single enclosure. This Power Commander V is available for select twin cylinder engines.
  • Retains all of the standard Power Commander V fuel control featurespowercommander_v_vs_pciiiusb
  • Allows +/- 20 degrees of timing adjustment
  • Map Switch Input – change maps on the fly
  • Adjust timing per cylinder
  • Raise your Rev Limit (only available on select models)
  • Built In Launch Limiter
NEW Power Commander V – PTi

On select models a new version of PCV is now available that’s perfect for forced induction applications. This new unit, PCV-PTi, comes with a Bosch 3 bar MAP/Temp sensor as part of the PCV harness for expanded capabilities built into the control    center software. res.

The PTi version of the PCV gives you the ability to modify your fuel curve based off a pressure (boost) table and/or temperature table. The pressure table gives you 3D mapping capability based on boost vs RPM, while the temperature table gives   you 2D mapping capability with up to 50 points of adjustment.

This new version of the Power Commander V – PTi is perfect for turbocharged or supercharged applications looking for precision, control, and reliability.

Related Products

The Power Commander V Accessories

AutoTune for Power Commander V

The Auto Tune kit monitors the fuel mixture (by installing the included Wide Band O2 sensor in the exhaust). It then sends this information to the Power Commander V and automatically corrects it while you ride. Each map that we offer has preset  Air/Fuel ratio values included that we find to be the best overall settings. This lets you simply plug in the unit and let it do the work. For Harley Davidson models we even monitor and adjust each cylinder individually for increased precision as on these models required fueling can vary significantly between the front and rear cylinder.

LCD Display for Power Commander V

The LCD Display connects to any Power Commander USB (some BMW models excluded) via a “quick disconnect” cable. It is designed to remain on the bike and is weather resistant. While connected, the unit will display all available data from the Power Commander. When the optional Multi-Function Hub is also installed all of its data is available for viewing as well.

Quick Shifter for Power Commander V

Normally during “up shifting” you must roll off of the throttle and pull in the clutch in order to engage the next higher gear. In racing (both drag and road race),  split seconds count. Rolling off the throttle, even slightly, slows your times and can be the difference between winning and losing. The Dynojet Quick Shifter (DQS) allows full throttle, clutch less shifting. This is done by momentarily cutting the fuel and or ignition, which unloads the transmission. During this time, the rider can shift up to the next gear without rolling off the throttle or using the clutch.

Power Commander V Related Accessories

Power Commander V Accessories

Power Commander V has all the same accessories Power Commander III USB has and more.  Below you can view some of these accessories.

pcv_complete_acc_layout